Montour County Rifles

Services

Accuracy Enhancement Package - Barrel Work - Muzzle Brakes - Action Work - Stock Work - Ceracoat Finishing - Reamer List

 

Accuracy Enhancement Package

MCR Accuracy Enhancement Package: $350

Enhance the accuracy of your factory rifle !!

 

All factory rifles could use a little help to perform better.  Here at MCR we provide an enhancement package that will take your factory rifle and make it perform much better than before.  Great pride and care is given to each rifle.  Your rifle is fully dis-assembled, cleaned and inspected first.  Should a larger problem be found we will discuss it with you prior to completing the enhancement package.  

 

The barrel is double dial bore indicated to unsure true concentricity using our proprietary barrel fixture.  The crown is single point re-cut and given a recessed crown.  The stock is prepped to ensure a 100% free floated barrel and the action is stress free pillar bedded using Devcon steel.  The bolt lugs are abrasive lapped to unsure even contact against the lug abutments.  The factory trigger is tuned for a crisp, clean break with little to no creep, minimal over travel and set at 2 1/2 - 3 lbs and safe*.  Finally the rifle is re-assembled, guard screws torqued to 60 in/lbs , scope rail or bases installed and blue loc-tited on.  Scope rings mounted and abrasive lapped to ensure perfect fit and alignment.  The scope is then mounted, reticle leveled and bore sighted.


 * Not all triggers can be set to this pull weight and be safe.  Triggers will be adjusted as close to this pull weight but must meet our safety inspection.*


Before After

 

a

 

Barrel Work

All barrel work is bore indicated true within .0002” or less of concentricity using live pilot indicating rods and Mitutoyo .0001” dual indicators. in MCR’s barrel fixture. All chambers are cut using live pilot reamers held in a floating reamer holder.

Install New Barrel Blank:

 

$265 and up

Metric Threads plus - $50

  • Single point turn and thread to a class 3A fit

  • Chamber to minimum head space

  • Single point crown

  • 320 grit finish

  • Custom engrave cartridge designation

Muzzle Brakes

 

Radial Vais Brake

  • Up to .875” muzzle dia. - $225
  • .876” muzzle dia - 1.0” muzzle dia - $235
  • Over 1.0” muzzle dia. - P.O.R.

 

Mini Mag Muscle Brake - $210

  • Available in 1/2-28, 9/16-24, and 5/8-24 Thread Sizes

  • Slabbed version only, fits muzzle dia. from .620” - .850”

 

3 Port Muscle Brake - $210

  • 5/8-24 Thread Size

  • slabbed version fits muzzle dia. from .685” - .990”

  • round version fits muzzle dia. from .685” - .990”

 

 

5port

5 Port Muscle Brake - $225

  • 5/8-24 Thread Size

  • slabbed version fits muzzle dia. from .685” - .990”

  • round version fits muzzle dia. from .685” - .990”

5portmag

5 Port Magnum Muscle Brake - $250

  • 5/8-24 Thread Size

  • slabbed version fits muzzle dia. from .685” - .990”

  • round version fits muzzle dia. from .685” - .990”

 

Timed MCR 3 Port Muzzle Brake / Simple in design but effective

 

  • .715” dia - 1/2-28 Thread Size - $200
    • can be turned to .650” dia. minimum
  • .885” dia - 9/16-24 Thread Size - $200
    • can be turned to .850” dia. minimum
  • 1.0” dia - 5/8-24 Thread Size - $200
    • can be turned to .965” dia. minimum

 

Action Work

ALL action work is indicated true within .0002” or less concentricity from the center line of the bolt bore using GTR Tooling and dual Mitutoyo .0001” indicators.

A full action blueprint can ONLY be done if a new barrel blank will be installed or if the barrel threads will be cut off and re-threaded. The action threads are bored and re-cut from .005” - .040” oversize for a full clean up making it not feasible to re-instal an existing barrel with standard threads. The fit will be too loose. I only blueprint the following actions.

Action Blueprint:

Remington models 600, 7, 700, 721, 722, XP-100 and 40X - $250

 

Includes:

  • Single point re-cut action face and internal locking lugs perpendicular to the bolt bore center line

  • Single point re-cut action threads concentric with the bolt bore center line

  • Single point re-cut rear of bolt lugs and bolt face perpendicular to the bolt body center line

  • MCR .250" Dual Draft Recoil Lug bored and fitted

Savage - $200

 

Includes:

  • Single point re-cut action face and internal locking lugs perpendicular to the bolt bore center line

  • Single point re-cut rear of bolt lugs and bolt face perpendicular to the bolt head stem

  • Single point re-cut rear of barrel nut concentric with barrel nut threads

  • MCR .250" Dual Draft Recoil Lug borede and fitted

Winchester 70 - $200

 

Includes:

  • Single point re-cut action face and internal locking lugs perpendicular to the bolt bore center line

  • Single point re-cut action threads concentric with the bolt bore center line

  • Single point re-cut rear of bolt lugs and bolt face perpendicular to the bolt body center line

Open Scope Base Holes:

 

Open actions scope base holes to 8-40 - $50

  • Action indicated true to bolt bore centerline and new scope base holes are bored and re-threaded on center

Open scope rail holes - $50

  • New holes will accept Torx T15 Fillister head screws

  • T15 Fillister head screws are included

Sako Extractor Conversion:

With a sako extractor conversion you can change bolt face dia. from factory size to 223, 308, mag or ultra mag. Fixes broken factory extractor and extraction problems. Gives a more positive extraction with less effort.

Remington models 600, 7, 700, 721, 722, XP-100 and 40X - $125

 

Includes:

  • Removal of factory extractor

  • 12L14 bushing silver soldered in and re-bored to specific bolt face dia. for a clean feed, feel and look

  • Will not change head space on pre-chambered rifles

  • All sako extractor parts are included

Bolt Knob Threading:

 

Factory Remington bolt handles only - $50

  • Knob NOT included

 

Bolt Fluting:

 

Remington bolt - $125

  • Spiral

  • Other designs available upon request

Savage Bolt - $140

  • Spiral

  • Other designs available upon request

Stock Work

Full Action Bed Aluminum Bedding Block Stock : $250

 

Pillar Bed - $250

 

Pillars are mfg. in house using 6061 aluminum

Open barrel channel - $50

 
  • If stock needs barrel channel opened up to accept a larger barrel contour than originally intended

Cerakoat Finishing      

Any metal on metal contact such as the bolt body o.d. may show signs of wear. To reduce this I recommend lightly coating your bolt with Mill-Comm TW25B.  

Complete Barreled Action(Single Solid Color ) - $250

Includes:

Scope Rail - $50

Scope Rings - $50

Scope ( air cure only ) - $150

Bolt Flutes Single Color, Bolt Body 320 grit Finish - $75

Bolt Flutes Single Solid Color w/ O.D. Single Contrasting Color - $100

Barrel Flutes Single Color, Barrel O.D. 320 grit Finish - $125

Barrel Flutes Single Solid Color w/ O.D. Single Contrasting Color - $150

Stock Single Solid Color w/ 1 Color Contrasting Speckles - $175

Stock Single Solid Color w/ 2 Color Contrasting Speckles - $185

Stock 3 Color GAP Camo - $250

Stock - $150

Multiple colors, patterns and designs available - P.O.R

 

 

Any firearm that has had it’s work completed and the customer fully notified must be paid in full within 10 days.

A $5 per day storage fee will be charged for any work not paid in full after 10 days.

 

Montour County Rifles |839 Jerseytown Rd. Danville, PA 17821| 570-437-2010| kevin@mcrifles.com